Skip to content

About

EFR32MG24 multi-protocol 2.4 GHz RC module with optional 459 MHz second link, and its setup controller.

Resources

Stars

4 stars

Watchers

3 watching

Forks

Latest commit

 

History

21 Commits

Folders and files

NameName
Last commit message
Last commit date
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

RC RF Module

A 2.4 GHz multi-protocol RC transmitter module and receiver on one board, built around the EFR32MG24 (RF-BM-MG24B2I module), with an optional second radio — an SX1278 (RA-01) — that carries the same channels on 459 MHz beside the 2.4 GHz link. One firmware serves both roles and both board variants.

Transmitter module takes the channels from a transmitter's encoder — PPM, or Multiprotocol serial frames — and sends them on nRF24, RLINK, FrSky D8, FrSky D16 (ACCST v1/v2, EU-LBT or FCC) or DSMX — and, experimental, Futaba S-FHSS and FASST (docs/FUTABA.md) — with the 459 MHz link beside it when the RA-01 is fitted
Receiver 8 servo outputs, PPM and SBUS; with the RA-01 fitted it listens on both bands and takes the servos from 459 MHz when 2.4 GHz goes quiet
Setup protocol jumpers, or a setup stored in the module: written over its serial pins with the hand-held Controller (this repository) or a terminal
TX panel (add-on) a small display, three or four buttons and a red / green LED on pins the board already has: mode, Single / Dual, input, bind and range check set on the module itself (docs/TX_PANEL.md)
Links of its own RLINK (two-way 2.4 GHz with telemetry, adaptive channels and power, alarms), nRF24 (the original 11 ms link), UK 459 MHz (10-byte hopping link)

Two board variants, one firmware

  • 2.4 GHz only — the RA-01 and its parts are left off. The firmware notices (no SX1278 answered) and runs 2.4 GHz only.
  • 2.4 GHz + 459 MHz — the RA-01 fitted. The firmware runs the 459 MHz link beside every transmitter mode (selectable Single / Dual) and the 459 MHz receiver beside every receiver mode.

The servo outputs are on the same pins for both variants (firmware/servo_pins.h).

What is where

Folder
firmware/ the EFR32 project (Simplicity SDK 2026.6.1, RAIL), build.ps1, cfg.ps1, prebuilt hex files — see firmware/README.md
controller/ the RF Module Controller: an STM32F103C8 box with a 128×64 display that sets the module up over its serial pins — STM32CubeIDE project, manual
hardware/rf_module/ the module carrier board: KiCad project, Gerbers, BOM and placement files
hardware/controller/ the controller board: KiCad project, Gerbers, BOM and placement files
docs/ operating quick sheet, flashing with an ST-Link, the serial input and setup command reference, the RLINK description, the TX panel, the experimental Futaba modes
CREDITS.md people, projects and components this builds on, with their licences

Start here

  1. Build a board — hardware/rf_module/README.md (what to order, what to leave off for the 2.4 GHz-only variant).
  2. Flash it — with only an ST-Link: docs/FLASHING_STLINK.md (the prebuilt firmware and a setup file for each role, no USB-serial adapter needed); to build it yourself: firmware/README.md.
  3. Use it — docs/QUICK_SHEET_EFR32_Module.md: connections, roles, modes, bind, failsafe, LEDs.
  4. Feed it — docs/SERIAL_INPUT.md: what a transmitter has to send (PPM or the Multiprotocol serial frame), and the text commands any programmer can use to set the module up.
  5. Controller — controller/README.md and controller/docs/MANUAL.md to build and use the setup box.
  6. TX panel — docs/TX_PANEL.md: the display, buttons and LED add-on for a transmitter module, its wiring and the three build versions (MULTI + PPM, MULTI only, PPM only).

Regulatory note

The 2.4 GHz side: every mode flies at the module's full power (about +19.5 dBm); DSMX at 22 ms only, FrSky D16 EU-LBT (Sub 0/1) with listen-before-talk (the D16 FCC versions, Sub 2/3/5, are for receivers with FCC firmware and have none), RLINK with a clear-channel check before every packet. The experimental Futaba modes (S-FHSS, FASST) have no listen-before-talk. The 459 MHz link uses the UK 458.5–459.5 MHz model-control band at 100 mW; check what your country allows before fitting the RA-01.

Licence

The firmware, the documentation and the hardware design files are released under the GNU GPL v3 (see LICENSE). The Controller (controller/) is under the MIT licence (controller/LICENSE). Third-party components keep their own licences, listed in CREDITS.md. The Silicon Labs RAIL radio library (a binary under Zlib) and two printf files under the Silicon Labs MSLA are not in this repository: they come with the Simplicity SDK, and build.ps1 copies them in. The firmware licence includes an additional permission to build it with that library (top of LICENSE).

About

EFR32MG24 multi-protocol 2.4 GHz RC module with optional 459 MHz second link, and its setup controller.

Resources

Stars

4 stars

Watchers

3 watching

Forks

Releases

Packages

Contributors

Languages