Important
This fork: experimental support for the FlySky Noble NB4+
This is a personal fork of GastonGelhorn/apextx.
It adds a build option NB4_PLUS_HW that runs the ApexTX NB4 firmware on the
Noble NB4+, based on a comparison of the stock NB4 and NB4+ firmware.
Status: tested on a real NB4+ (2026-10-16) – ApexTX boots and the internal RF binds a receiver and drives a servo (Enhanced PHY mode). Still experimental. The earlier English-language power-off is fixed (it was a reentrant page rebuild overflowing the UI stack). Back up the internal flash before flashing.
- Overview and result in short: docs/nb4plus/README.md
- Current state, open questions, test plan, how to help: docs/nb4plus/STATUS.md
- Step-by-step test guide (backup, flash, checks, going back): docs/nb4plus/TESTING.md
- Regions (CE/FCC), RF module and receiver updates: docs/nb4plus/UPDATES.md
- How the findings were obtained: docs/nb4plus/METHOD.md
- All findings with evidence and certainty: docs/nb4plus/FINDINGS.md
- All tests and their results: docs/nb4plus/TEST_RESULTS.md
- Tool to back up the external flash before installing (simulation only): tools/nb4plus-nor-reader
- All changes compared with ApexTX: compare view
Everything below this box is the original ApexTX README.
ApexTX is independent firmware for the original FlySky Noble NB4 transmitter. It adds a car-focused interface, responsive steering and throttle controls, configurable hardware assignments, AFHDS3 receiver support, race timing, telemetry, audio, and an expanded on-device filesystem.
The current project version is 0.1.0-alpha.3, based on EdgeTX 2.12.4.
The original Noble NB4 build includes:
- Full-color dark and light themes designed for the NB4 display.
- Portrait and landscape layouts with the same controls and information in both orientations.
- A live racing home with steering, throttle and brake, trims, lap timing, RF signal, and TX/RX battery status visible at a glance.
- Direct car setup for steering travel, throttle and brake curves, channel limits, ABS, failsafe, telemetry, and receiver binding.
- Detect-and-assign configuration for the wheel, trigger, grip buttons, switches, trims, interface navigation, and racing actions.
- Integrated lap timing, history, pit tools, spoken alerts, USB modes, and English or Spanish sound packs.
- A maintained, testable firmware base that can absorb selected upstream improvements while keeping the NB4-specific interface and AFHDS3 support.
| Portrait home | Landscape home |
|---|---|
![]() |
![]() |
| Throttle and brake curve: portrait | Throttle and brake curve: landscape |
|---|---|
![]() |
![]() |
| Settings modal: portrait | Settings modal: landscape |
|---|---|
![]() |
![]() |
See the complete interface gallery for vehicle setup, race timing, telemetry, and physical-control assignments.
The currently supported target is the original Noble NB4:
PCB=PL18
PCBREV=NB4
The NB4+ target currently compiles as an experimental port candidate. It has not been validated on hardware. NB4 Pro and NB4 Pro+ require separate board ports and are not supported. See the Noble compatibility and feature matrix.
ApexTX is unofficial firmware. It is not made by, endorsed by or supported by FlySky, and installing it replaces the factory firmware on the transmitter.
Read this before flashing anything:
- There is no warranty. The GNU GPL version 2 under which this is published disclaims one explicitly, and that is not a formality here. You are responsible for what happens to your radio and to your car.
- You can leave the radio needing recovery. An interrupted first installation is recovered through the STM32 ROM DFU, which means opening the case to reach an internal button. Back up the original contents first, as FLASH.md describes.
- The RF setup carries no vendor qualification. The AFHDS3 settings this firmware uses are not covered by any FlySky specification or approval. They work on the radios ApexTX has run on, and that is the extent of the claim.
- Nobody certifies the release binaries. The archives attached to a release are built by GitHub Actions from the tagged source and nothing more. There is a hardware checklist in the documentation, but no automated step enforces it, so treat a release as a build that compiled and passed its automated tests.
- Check what you are allowed to transmit. Radio regulations differ by country. Complying with the ones that apply to you is your responsibility.
- Test before you drive. Check failsafe with the wheels off the ground, every time you change firmware or rebind.
The firmware is under active development and is tested on an original Noble NB4. The maintained configuration uses the USART6 AFHDS3 route and English firmware strings. The interface can be switched between English and Spanish, independently of the single English or Spanish voice pack installed on the expanded storage volume.
Device-specific factory images, calibration data, OTP contents, and local build artifacts are intentionally excluded from this repository.
The short form of the verified device build is:
cmake -S . -B build/nb4-device \
-DPCB=PL18 -DPCBREV=NB4 -DCMAKE_BUILD_TYPE=Release \
-DPython3_EXECUTABLE="$PWD/.venv/bin/python" \
-DNB4_RF_PROFILE=RECOVERED_USART6 \
-DTRANSLATIONS=EN -DDISABLE_COMPANION=ON
cmake --build build/nb4-device --target firmware-size -j8See the maintained NB4 documentation for environment setup, flashing, hardware details, and validation:
- NB4 overview
- Interface gallery
- Noble model compatibility
- Build instructions
- Install from the FlySky firmware
- Update an existing ApexTX installation
- Install English or Spanish audio
- Hardware notes
- Validation checklist
- Control latency
- Hardware checklist before a release
- Release process
- Contributing
- Security policy
- Support
- Changelog
This project retains the EdgeTX source layout so upstream releases can be integrated with a reviewable diff. Changes specific to the Noble NB4 are kept in the NB4 target, interface, protocol, tests, documentation, and tooling wherever possible.
ApexTX is an independent community project. It is not an official FlySky or EdgeTX release.
This repository is derived from EdgeTX and is distributed under the GNU General Public License version 2. See LICENSE. Existing copyright and attribution notices remain with their respective authors.






